IP500 V2 安装

机架安装

rack mount

如果需要安装到 19 英寸机架系统中,IP500 控制单元和 IP500 外部扩展装置可进行机架安装。每个单元需要一个 IP500 机架安装套件 (SAP 700429202)。

套件包括:

机架安装支架和用于将支架连接到单元的螺钉。
用于机架连接的螺母和螺栓。
支架和用于整理线缆的线缆扎带。

 

如下图中所示,机架安装支架可用在单元的几个位置中。IP500 系统中使用的 IP400 外部扩展装置也可进行机架安装,但是需使用独立的 IP400 机架安装套件。

环境要求
除了 IP Office 系统的现有环境要求外,在对装置进行机架安装时,必须考虑下列额外因素:

1.机架定位 - 确保遵守机架制造商的安全说明。例如,检查机架腿已放下并且固定支架已用于防止倾倒。
2.较高的工作环境 - 如果安装在封闭或多装置机架装配中,则机架环境的工作环境温度高于室温。因此,应考虑将设备安装在与制造商指定的最大环境温度 (Tma) 相符的环境中的情形。
o 工作温度:0°C (32°F) 到 40°C (104°F)。
o 工作湿度:10% 到 95% 非冷凝。
3.气流减少 - 机架中的设备安装应当如此:即设备安全操作所需的气流量不会受到影响。必须维持适当的通风。不应覆盖或堵塞 IP500 控制单元的侧面通风槽。
4.机械装载 - 机架中的设备安装应当如此:即不会由于不均匀的机械装载而导致危险状况。
5.电路过载 - 应考虑设备与供电电路的连接,电路过载可能会影响过电流保护和供电线。解决此问题时,应适当考虑设备铭牌额定值。
6.可靠的接地 - 应当维持机架安装式设备的可靠接地。除了直接连接外,还应特别小心分支电路的电源连接(例如,使用电源板)。
7.icon_warning 只能使用安装套件随附的螺钉 (M3 x 6mm) 将支架连接到控制单元。

 

ip500 rack mount

icon_warning 只能使用安装套件随附的螺钉 (M3 x 6mm) 将支架连接到控制单元。

 

© 2010 Avaya LLC
15-601042 CHS Issue 21.e.-
14:05, 30 March 2010
(rack_mounting.htm)

Performance figures, data and operation quoted in this document are typical and must be specifically confirmed in writing by Avaya before they become applicable to any particular order or contract. The company reserves the right to make alterations or amendments at its own discretion. The publication of information in this document does not imply freedom from patent or any other protective rights of Avaya or others.

All trademarks identified by (R) or TM are registered trademarks or trademarks respectively of Avaya LLC. All other trademarks are the property of their respective owners.

Last Modified: 10/03/2010