IP Office Essential Edition - Basic Edition Phone Admin: Ring Settings
Line Ringing Pattern
This option is new for IP Office Essential Edition - IP Office Essential Edition - Basic Edition 6.1 and higher+. It allows the ringing pattern used on a phone to be determined by the line on which the call has arrived. This feature is not supported on BST phones which only use the personal ring pattern setting.
•
Calls forwarded, sent to call coverage or to a hunt group will always use the line ring pattern.
•
Incoming calls transferred to another station ring with the assigned ring pattern followed by two transfer beeps.
•
Transfer returning outside calls also ring with the two transfer beeps.
•
Since only one audible alert can be heard at a station at one time, the ringing pattern present at that extension that has multiple lines alerting is for the line that pattern associated with the next alerting line for that extension.
•
The actual ring patterns vary depending on the phone type.
•
Calls direct to an extension will use the line ringing pattern unless the user has Override Line Ringing active.
•
Through IP Office Manager, ringing patterns can also be assigned for DID routes. These override the setting of the line.
1408/1416/9404/9408/9504/9508 Phone
1.
At either of the first two extensions on the system, with the phone idle, press Admin.
2.
Use the up or down arrow buttons to scroll the display to System Administration. When shown, press Select.
3.
Use the up or down arrow buttons to scroll the display to Lines. When shown, press Select.
Use the up or down arrow buttons to scroll the display to Ring Pattern. When shown, press Select.
5.
At the Line: prompt, enter the desired line number 01 to 64.
6.
The current setting is displayed.
7.
Enter the ring pattern number 1(default) to 8.
•
Alternatively use the left or right arrow icons to toggle through the settings or Default to return to the default setting.
8.
Use the up or down arrow buttons to select another line.
•
Exit programming by pressing PHONE/EXIT. Alternatively use the Back button to move to another menu.
M7324/M7324N/M7310/M7310N/T7316/T7316E Phone
1.
At either of the first two extensions on the system, with the phone idle, press Feature **config (ie. Feature **266344).
•
If the system has a system password set, it is requested. Enter the password.
2.
The phone displays System Admin.
3.
Dial #209. The phone displays Ring Pattern.
4.
At the Line: prompt, enter the desired line number 01 to 64.
5.
The current setting is displayed.
6.
Enter the ring pattern number 1(default) to 8.
•
Alternatively use the Next Data or Previous Data buttons to change the setting or press Remove to return to the default setting.
7.
Press the Next Item or Previous Item button for the next or previous line.
•
To exit phone based administration at any time, press the Release button. To select a different process use the Next Procedure or Previous Procedure buttons or dial another feature code.
ETR 18D/ETR 34D Phone
1.
At either or the first two extensions on the system, with the phone idle, press Feature 0 0 followed by two presses of the first intercom or call appearance button.
2.
System Administration: is shown on the display.
3.
Dial #209. The phone displays Ring Pattern.
4.
At the Line: prompt, enter the desired line number 01 to 64.
5.
The current setting is displayed.
6.
Enter the ring pattern number 1(default) to 8.
•
Alternatively use the Next Data or Previous Data buttons to change the setting or press Remove to return to the default setting.
8.
Press the Next Item or Previous Item button for the next or previous line.
•
Exit programming by pressing Feature 00. You can also exit programming mode by lifting the handset, then placing it back in the cradle.
Performance figures, data and operation quoted in this document are typical and must be specifically confirmed in writing
by Avaya before they become applicable to any particular order or contract. The company reserves the right to
make alterations or amendments at its own discretion. The publication of information in this document does not
imply freedom from patent or any other protective rights of Avaya or others.
All trademarks identified by (R) or TM are registered trademarks or trademarks respectively of Avaya LLC. All other
trademarks are the property of their respective owners.
up or down 
arrow buttons to scroll the display to System Administration. When shown, press Select.
left or right 
arrow icons to toggle through the settings or Default to return to the default setting. 
Feature **config (ie. Feature **266344).