Please enable JavaScript to view this site.

IP500 V2/V2A IP Office Basic Edition

This type of module can be used to add additional RJ45 ports for digital telephones. Through the system configuration, each module is set to either DS mode for support Avaya DS digital telephones or BST mode ports for supported Avaya BST digital telephones (DS ports only on IP500 control units).  See DS16B2/30B2 Port Mode Selection.

The modules are available in 16 and 30 port variants, referred to as the IP500 DS16B and IP500 DS30B respectively. The DS16B and DS30B have now been superseded by the DS16B2 and DS30B2 models which provide the same functionality.

ip500 ds30 3d

Feature

Details

Locales

Supported in all IP Office locales.

Minimum Software Level

DS16B/DS30B: IP Office Release 9.0. IP500 (DS only) and IP500 V2/V2A (DS or TCM). For IP Office Release 8.1 (Service Pack 9+) these modules only support DS ports.

DS16B2/DS30B2: IP Office Release 10.1. Also IP Office Release 9.1 SP12 and IP Office Release 10.0 SP5.

Included

Power supply unit (see below) and Expansion Interconnect cable.

Power Supply

The module is supplied with a Earthed 3-Pin, 60W external power supply module. The PSU has an integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13 power cord for the external PSU is required but is not supplied with the module.

Mounting

The module is designed as a free-standing module that can be stacked on or under other IP Office modules. The module can be wall or rack mounted using the IPO IP500 RACK MNTG KIT V3.

Dimensions

Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".

Weight

Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30)

DS16B/DS30B Upgrade Behavior:
For DS16B/DS30B modules the process of loading the appropriate firmware for the selected mode or upgrading takes up to 10 minutes during which time the module is not available.

DS16B2/DS30B2 Upgrade Behavior:
The behavior of DS16/30B2 during firmware upgrade or switching modes differs from other external expansion units:

During the firmware upgrade, the unit remains operational and can make and receive calls.

Once the upgrade is completed (approximately 9 minutes) the unit reboots and takes about 45 seconds to return to normal operation.

 

Module Front

ip500_ds30b_front

Port LEDs

Green Flashing = Phone detected.

Green On = Phone active.

Module Center LED

The center LED on all external expansion modules is used to indicate the overall state of the module as follows:

Red flashing = Module starting up/Loading firmware.

Red on = Error.

Green on = Module okay.

Module Rear

ip500_ds30b_rear

Port

Description

DC I/P

DC power input port. Used for connection of the power lead from an Avaya earthed 60W external power supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord for the external PSU is required but is not supplied with the module.

DS

RJ45 socket. Digital Station port. Used for connection of IP Office supported DS phones. If connected to an out-of-building extension, the connection must be made via additional IROB barrier devices in addition to the buildings primary protection. The module must also be connected to a protective ground.

DTE

9-Way D-Type socket. For Avaya use only.

EXPANSION

RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the Expansion Interconnect cable supplied with the module.

earth symbol

Protective Ground point. Use of a protective ground is required for all installations, see Grounding (Earthing). Where the module is connected to analog extensions in another building, an IP Office Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building Connections.

Part Codes and Related Equipment

All expansion modules are supplied with a base software level and should be upgraded to match the core software of the control unit in the IP Office system. Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not include a locale specific power cord for the external PSU or any phone extension cables.

Item

Variant

Country

SAP Code

IPO IP500 EXP MOD DS16B DGTL ST

16 Ports

All

700501585

IPO IP500 EXP MOD DS30B DGTL ST

30 Ports

All

700501586

IPO IP500 EXP MOD DS16B2 DGTL ST

16 Ports

All

700511093

IPO IP500 EXP MOD DS30B2 DGTL ST

30 Ports

All

700511094

IEC60320 C13 Power Cord

plug_ie60320_c13

CEE7/7

Europe

700289762

BS1363

United Kingdom

700289747

NEMA5-15P

America

700289770

Mounting Kit

IPO IP500 WALL MNTG KIT V3

All

700503160

 

 

Performance figures, data and operation quoted in this document are typical and must be specifically confirmed in writing by Avaya before they become applicable to any particular order or contract. The company reserves the right to make alterations or amendments at its own discretion. The publication of information in this document does not imply freedom from patent or any other protective rights of Avaya or others. All trademarks identified by ™, ® or © are registered trademarks or trademarks respectively are the property of their respective owners.

© 2022 AVAYA
Issue 38.g.-
Tuesday, July 19, 2022